CRANBOURNE SWAP MEET
CRANBOURNE RACECOURSE

THIS EVENT WILL CATER TO ALL MAKES AND MODELS OF VINTAGE, VETERAN AND CLASSIC MOTOR VEHICLES PLUS A COMPREHENSIVE RANGE OF PERFORMANCE EQUIPMENT. INCLUDING AN AREA DESIGNATED FOR VEHICLES FOR SALE.

ORGANISED BY FORMER NATIONAL DRAG RACING IDENTITY

SELLING SITES FROM $25. GENERAL ADMISSION $5
SPECIAL NOTE ENTRY BEFORE 8 AM $10

EMAIL pro51447@bigpond.net.au

GRAHAM ROSE 03 9585 6567 / 0428 394 249

And look out for me in a white VT with couier on the sides and a trailer with LE Monaro mags on it I have lots of HQ- HZ stuff.

Daniel
0428 319 883
(Postcode 3030)
Email Button
"My Shed"

I am fitting a windscreen back into my fj ute. I have new rubbers. Any tips or tricks that people know about when fitting a windscreen?? Should I use sealant with new rubbers??

Went on a hunt for old holdens last sunday, well what a day i and a mate had . This fj door with its glass was one of them.Check the old f#$d we found out on the mud flats. Off Wyndham WA................
spud
Kununurra 6743

Yella terra Head with YT on the valves and Double valve springs located in werribee is now sold
Daniel
0428 319 883
(Postcode 3030)
Email Button
"My Shed"

left the room to go check Oldholden and get the pics for the head go to ask the missus something and there she is cleaning the silastic of the bottom of the motor

Idler arm info there are a few guys selling idlers with lugs, I have been told by someone who has tried one of these that it is a no go re angles and toe in.even some of sellers state they may not be suitable..I would like to get flat idler with no lugs, any ideas was thinking of grinding lugs off..

Here is a pic of the engine i'm doing up and yes its in the house Also I have a YELLA TERRA head for sale in melbourne local pick up will post up pics of it.

Daniel
0428 319 883
(Postcode 3030)
Email Button
"My Shed"

Can any one tell me if a HR crossmember modified to fit a FB would fit an FJ.

time to sell up the 202!

its a red 202 with 9 port head, has done roughly 5000km since rebuild and was built to run 11s reliably on boost

bottom end
block torque plate bored and honed, decked, tunnel line bored and honed
fully balanced
stock stroke crank - linished
ACL bearings throughout
prepped starfire rods - resized and shotpeened
ACL race series piston
ACL rings
bung in sump for oil return

ignition
HEI distributor
8mm topgun leads
bosch coil

top end
custom grind hydraulic cam - clive cams
copper head gasket
o-ringed
chambers in head opened up to reduce comp (runs around 8:1 comp)
mild clean up in the ports
yella terra roller rockers
aftermarket rocker cover

has an auto flexplate but will NOT include stall converter

Hi all,

Have an issue with my FJ ute. I have 17inch wheels on it. The drivers side front wheel seems to stick a little out of the guard (actually on the lip) and the passenger side is about 1 inch inside the guard. I have changed the drivers side guard and it is still the same.

Can anyone give me any suggestions or what to look for in regard to why this might be occurring.

I have attached a pic of the front drivers side guard to show everyone.

Jason

Worked red 202 with 2 barrel setup $500 ono
HQ-HZ rear Wagon and Sedan doors $40 each
Tonner walk off front no bumper $80
tonner petrol tank $20
cut down wagon petrol tanks for gas $20
Commodore Bench Bucket seat setup will suit HQ-WB $200
HQ bonnet $50
HJ-WB bonnet $50
HQ statesman nose cone and support panel with square headlights $100
NOS Standard HQ fuel gauge $50
Celica 5 speed belhousing and clutch to suit holden 6 $150
VQ statesman Mags $150

Daniel
0428 319 883
(Postcode 3030)
Email Button
"My Shed"

Hi all :)

If anyone has the cardboard panels for around the back seat area of the FX or FJs... to make some templates from them to get some reproduced.
Give me an email on rusty@oldholden.com if you can help and we can sort something out.

thanks, wish me luck !

Hi I have just put a 308 engine into my fj holden and am looking for information on what type and size of radiator will fit
Regards Dave dattrill@westvic.com.au 0488646585

Hi
I need a phone number for an approved engineer in brisbane. I have a fj ute and want to know some info about getting it re-registered these days. It is slightly modified. Need to know about seatbelts, demisters, indicators and those things. Any help is greatly appreciated.

Cheers

Rosey

I have a 3.08 Course spline Banjo Diff centre for Sale located in Werribee askin $150 ono for it had new bearings about 2 months ago

Daniel
0428 319 883
(Postcode 3030)
Email Button
"My Shed"

http://cgi.ebay.com....

also have an almost complete car as well, see my other items listed

I have a worked 202 motor with 2 barrel setup and yella terra head for sale asking $500 ono for it running motor located in werribee vic

Daniel
0428 319 883
(Postcode 3030)
Email Button
"My Shed"

hi, i have an fj and i am going to modify it to put fc headlight rims on as i think the FC rims look mean and would really make focal point, i have a picture in my head but have never seen it done, does anyone have a picture or if someone has the time able to photo shop it as i am useless at photo shop. would be apprieciated, any feedback on the idea would be good too

Hi I am after any info about registering fj holdens in qld. I have inhereted an fj ute and am starting the rebuild. I need to know if you need demisters, lights, seat belts, that sort of thing. Any help would be great

I pulled these off a fj sedan yesterday and was wondering if anybody knows what type they are. They dont look home made. They fit on the tyre side of the spring and it looks like the front bracket was tack welded at some stage.

FX with Waggott head in Canberra - FX-FJ Nationals Dec06

like the title says, how much would a fully (20yrs ago) rechromed and wrapped in newspaper in the shed ever since FJ grille be worth?

hi all im from perth WA and have an FJ,this site has helped with many questions before so heres another, i am in some serious need of a new subfame, which i know its hard to get, i have a good enough to use r/h side if i cannot get one but i really need the left side, would prefer the complete setup but i am willing to chop and match, hope someone can help. my email is dianne.donald@bigpond.com.au or my mobile 0422 689 650 i am willing to pay for the courier if the item is right and needs to come from another state
thanks
josh

Howdy, need someone with knowledge in EJ/EH holdens to do some serious rust repairs in a EJ windowless panelvan.

Any of you blokes recommend anyone- NW suburbs but willing to travel.
cheers
cass

I have a worked 202 motor with 2 barrel setup and yella terra head for sale asking $500 for it running motor located in werribee vic

Daniel
0428 319 883
(Postcode 3030)
Email Button
"My Shed"

Looking for a grey motor to rebuild for a rat rod project, Looking to spend no more the $150 on the engine. I'm from Far North Queenland

Here's your rocker cover after a weeks worth of sanding then $30 at the polishers and finally it's on the yoot. Looks good although close up inspection can easilly see another $30 at the polishers would be even better.

FOR SALE

1 x ACL "race series" Full engine gasket kit. NEW IN BOX.

Suits VN-VT 5.0L Engine. Or should fit any 308 engine with 304 (VN-VT) heads.

ACL Part Number: GS150GTR

I payed $159 SELL PRICE IS $140 (including FREE postage to anywhere in Australia).

Drop a message here if interested. Be quick as advertised on other forums etc. will not last long.

Cheers
Jason

I've got a few "things for sale" , click on the pic that interests you and you'll get a bigger picture.
I promise i'll spend ya money on an oldholden :-}}

"Republic of Dusty's Shed"
EMAIL
(postcode 3380)

"Don't walk away in frustration...Kick the crap out of it"